0.30 Discussion Thread

I found some weird stuff in the new steel factory:
-car disappearing
-light glitching
-you can drive through some things

Video:




Also i would like to share my opinion about the enclosed trailer. I think it's too small, because most of the cars destroy the trailer when i try to drive in or don't fit at all. It would be cool to see a bigger version of it or just make it a little wider.

 

Trunk trim of traffic Pessima is still missing

 

I didn't try to load GPU, I just compared the performance reduction of CPU, usually I play in 4k and there are no problems with GPU loading, and vulkan is not suitable for me because there is no HDR, and on my Oled it is critical..

 

how to launch with vulcan by default ?
--- Post updated ---
hello, I have a pretty huge problem: the maps don't launch and stay like that

(I left the map like that for 20 minutes and nothing changed) (same result in safe mode)

there are also some other problems: when I launch the game it is by default in English instead of French and I have to put it back in French manually each time. and also the fact that all the parameters that I had set in the game has been reset (like every new version)

 

strangely, I have a computer on ryzen 5 3600 16 GB gtx 1650, but the map has 70 fps as it was before.

 

CPU utilization has gone up on this card, you had 100% GPU utilization and still have, we're talking about completely different things,

 

When a vehicle is on a scenario start trigger in 0.29 you would hit (by default) the "Select" button, but in 0.30 you now hit the "A" button. Although... if your gear shift buttons are "A" and "X" you can no longer shift into Drive or 1st gear because it opens up the scenario start screen instead. You can reverse out of this, but I feel it would be better to have left the scenario start button to be "Select" so you wont have this issue.

I still like the old method better - so I left my original comment above - BUT I just realized you can hit "B" to close the popup and then the "A" button allows you to shift into gear. So this is a non-issue. Would have deleted this post if I could.

 

(tested in safe mode) On the parking spaces near the beach/sea on West Coast, there's a dirt road effect on the asphalt. This effect does not occur on the asphalt in front of the parking spaces:

 

The new gear shift logic seems to cause synchro damage when shifting manually (using a controller), even with clutch and throttle assists turned on.

When I first ran beamng 0.30 I got damage on every single gear in the 200BX track variant. Issue is a bit less consistent in safemode but still present.

Attaching a video of the 200bx doing it. All settings are default, this is running in safemode, all gearbox assists are on (shot of the menu at the end). Safemode command line options: " -console -nonvidia -safemode"

edit: I don't know if this'll produce a full size screenshot but you can see the clutch is only activated for an extremely short period of time during gear shifts (obviously this screenshot isn't in safemode)

 

What?
I dont see difference

 

Found invisible wall on a shed in the WCUSA refinery, I'm right up against the wall in the screenshot
Screenshotted in safe mode

 

- New Upfit towhitches are too far forward on the pickup, they are correct on the van

- Burnside chopped and channeled body roof accessory is not always placed correctly

and the roofbars themselfes are off a bit compared to the standard roof

Taxi sign could be better as well

 

What kind of logic is this then? What's the use of the clutch assistant at this point? If the car goes into gear the instant I let off the button with clutch assistant on, why does the clutch assistant option even exist if it does nothing anymore?

The gear passing through neutral on button down and into gear on button up should only shift the gear lever that fast. Clutch assistant should still be preventing gear grinding, otherwise why does it even exist as an option?

 

Loving the update so far. When float shifting gears in the T-Series with a H-pattern controller, I'll receive "synchro damage" notifications when the shifts are not absolutely perfect. It should be "gear damaged" as a gearbox like that would typically be unsynchronized. Same thing is noticed when shifting into reverse while rolling. Reverse is typically unsynchronized so that would result in gear damage.

Related to float shifting, is there a jbeam defined tolerance that can allow some minor rpm variation to simulate a heavy truck transmission?

 

And how will you see it if you have 100% load on your "weak" GPU?)

 

The train tracks on the bridge appear to have incorrect (way too high?) collision

also multi track drifting (into a concrete barrier)
Completely unnesscary gripes and probably won't be noticed by the playerbase ever, but driving on train tracks can be fun

 

Same issue here (tires deflates):

 

cars with dual clutches don't move without touching the throttle